AFT Blog

Welcome to the Applied Flow Technology Blog where you will find the latest news and training on how to use AFT Fathom, AFT Arrow, AFT Impulse, AFT xStream and other AFT software products.

Start your engines! Modeling an Inertial Pump Startup

There are many (six!) ways to define a pump transient event in AFT Impulse. This gives you great flexibility in creating a model that behaves the way you want it to. One thing true for all pumps is that they must be started at least once. Pump startups often cause significant transient effects on the system so you may wish to model this with AFT Impulse. Even narrowing your pump transient down to a startup, there are still four models left to choose from: Without InertiaStartup With Inertia and No Back Flow or Reverse SpeedStartup With Inertia - Four Quadrant, Known...

Continue reading
  7889 Hits

When to Begin? Time and Events in Transient Studies

To define any transient event in AFT Impulse or AFT Fathom XTS the application must know when it begins. To do so, the user should know how time and event logic is approached in AFT’s transient solvers. In this article, we will discuss the three different time bases used in the applications, the selection of a single or repeating event, and the many possible triggering events that can start the user defined transient. The user defines these items in the Initiation of Transient section of the junction’s Transient tab. The requirements for each junction can vary, but the general approach applies...

Continue reading
  4926 Hits

Inherent vs. Installed Control Valve Curves and How They Relate to AFT Software

As tech support engineers, we sometimes receive questions from users confused about what control valve characteristic curve (inherent or installed) they are inputting into AFT Fathom, AFT Arrow, or AFT Impulse. The inherent control valve characteristic curve plots the valve open percent versus the percent of maximum Cv. This curve is true regardless of the system effects on the valve. The installed control valve characteristic curve plots the valve open percent versus the flow through the valve, and this plot is dependent on the conditions specific to the system. For example, if the control valve flow setpoint is fixed at 250...

Continue reading
  10370 Hits

Tolerable Convergence

Trying to design and analyze piping systems can be a complicated, and difficult task for engineers. This was especially true before the advent of easily accessible computer technology. Hand calculations required hundreds of hours of painstaking work, by entire teams of people. Great care had to be taken to ensure the reliability and accuracy of the results. Human beings do make mistakes, after all.

In today’s engineering world, there are a multitude of computer tools designed to make the design process simpler, faster, and more reliable, such as AFT’s family of analysis products. AFT products revolve around graphically based, drag and drop interfaces that makes creating a computer model of piping systems quick, and easy. Being able to create simulation models with little effort, however, can be a bit of a double-edged sword.

Continue reading
Tags:
  4049 Hits

Give me some details about Detailed Tees!

Frequently in tech support, when a difficult-to-converge model comes in, one of the first things we check is whether or not any tees in the model are being modeled as detailed tees. The reason for this is that the hydraulic calculations involving detailed tees can be complex due to the interdependence between velocity and pressure loss for each pipe connected to the tee. Iteration must, therefore, be performed to find a pressure loss and flow through each connecting pipe that agrees with the rest of the flow and pressure solutions in the model. This begs the question, then, what calculations are...

Continue reading
  13018 Hits

What Does “Head (HGL)” Mean for Submerged Pumps and Exit Pressures?

In AFT Fathom and AFT Impulse, it is possible to model a submerged pump where a short and possibly frictionless suction pipe for the pump’s inlet does not need to be modeled.  When modeling a submerged pump, there are two options available for specifying the system inlet boundary condition at the pump suction.  As shown in Figure 1 below, the Submerged Pump’s Suction Pressure can either be specified as “Head (HGL)” or “Pressure”.   Modeling a submerged pump is not the only time where the “Head (HGL)” or “Pressure” choices will arise.  If an Exit Valve (i.e., a valve that discharges...

Continue reading
  10087 Hits

Know Your Pump and System Curves - Part 1

AFT Fathom can easily generate a pump and system curve for your piping system.  Creating a pump and system curve for a simple system with a single flow path and no control features is an easy and typically well-understood process.  However, as piping systems are quite complicated with lots of branch points, control features, and dynamic interactions, creating a useful system curve can quickly become a common source of confusion.  This three-part blog series is going to help clarify concepts regarding pump and system curves to better understand them.   This Part 1 blog will discuss the basics of what pump...

Continue reading
  86258 Hits
Log in

Login to your account

Username *
Password *
Remember Me

Create an account

Fields marked with an asterisk (*) are required.
Name *
Username *
Password *
Verify password *
Email *
Verify email *
Captcha *
Reload Captcha
© 1996 - 2024 Applied Flow Technology